Comdial DX-120 KSU1 Processor - K16UM1.F20 Software

S/N 720000C72800079

This card can be used to replace a defective processor in the DX-120 KSU1.  It has been fully tested and the battery has been replaced.


Condition: Refurbished - 90 Day Warranty

$80.00 (Free USPS Shipping)

Call or E-Mail To Order. 




 

Comdial DX-120 KSU1 Processor - K16UM1.F19 Software

S/N 720000F71700837

This card can be used to replace a defective processor in the DX-120 KSU1.  It has been fully tested and the battery has been replaced.


Condition: Refurbished - 90 Day Warranty

$80.00 (Free USPS Shipping)

Call or E-Mail To Order. 

 

 

 Comdial DX-120 7221 DPM16 (2 Available)

16 Port Digital Station Card 7221-00.  The card does not include the box, but it is in its original, unopened anti-static bag.


The DPM16 module expands the DX-120 system capacity of digital ports DET (Digital Executive Telephones) and DSS consoles. Each digital port is comprised of a proprietary octal ASIC transceiver. There are three datachannels in operation at each digital port via the octal transceiver. One channel is used for call processing control of digital terminal functions/operations and two channels are used for the digital voice channel requirements. The DPM16 is controlled directly from the 408M/E. Therefore, there is no heartbeat LED located on the DPM16.
• Each digital station interface is protected against circuit wiring shorts by an over-current protection Polyswitch.  The digital station circuit requires only one cable pair to operate and is not polarity sensitive.• Physical connection of digital port terminals (DET and DSS) to the DPM16 module is made through convenient RJ-12 connectors along the bottom edge of the module.• Two DPM16 (Digital Port Module, 16-port - i.e., 16 digital phones) modules can be added to each KSU of the DX-120 system.• These modules expand the DX-120 system extension capacity to a maximum of 40 digital ports in each KSU (80 total digital ports).• DPM16’s are installed by connection to the 408M via the Extension Expansion module connectors (“J2”and “J3.”)• The DPM16 board has eight RJ-12 jacks.• Each RJ-12 jack has four wires so you plug two phones into each jack.• You cannot do a Off-Hook Voice Announce (OHVA) to a phone that is plugged into the DPM16. However, you can do a OHVA from a phone that is plugged into a DPM16 board.

Condition: New - Open Box (1 Year Warranty)  $60.00 (Free USPS Shipping)

Call or E-Mail to Order. 

 

Comdial DX-80 & DX-120 7210 COM4 (2 Available)

The card does not include the box, but it is in its original, unopened anti-static bag.

The COM4 module is installed in the dedicated position via J1 of the 408M/E. The COM4 interfaces four loop-start CO lines. Since one COM4 may be installed in KSU1 and one COM4 may be installed in KSU2, you can expand the DX-120 system loop start CO line capacity to support up to 16 loop start CO lines.

 

You can add one COM4 to KSU1 and one COM4 to the KSU2. These modules expand the DX-120 system loop start CO line interface capacity to a maximum of eight loop start CO line ports in each KSU (16 total loop startCO line ports when used in KSU 1 & 2).• When adding a COM4 to either KSU, connect to the 408M/E via the COM4 module ribbon cable.- This ribbon cable has the logical system address of SLOT 5 in both cabinet 1 (KSU1-408M) and cabinet 2 (KSU2-408E).• COM4 modules are installed using four 2.0 cm (brass) standoffs.• Always install the COM4 module beneath the CPM module (in KSU1) by first removing the CPM, installing the COM4, and then re-installing the CPM. This is required whenever you install the In-Skin Voice Processor.

 

Condition: New - Open Box (1 Year Warranty)  $50.00 (Free USPS Shipping)

Call or E-Mail to Order. 

 

Comdial DX-80 & DX-120 7210 COM4 (1 Available)

The card does not include the box, only what is pictured.

The COM4 module is installed in the dedicated position via J1 of the 408M/E. The COM4 interfaces four loop-start CO lines. Since one COM4 may be installed in KSU1 and one COM4 may be installed in KSU2, you can expand the DX-120 system loop start CO line capacity to support up to 16 loop start CO lines.

 

You can add one COM4 to KSU1 and one COM4 to the KSU2. These modules expand the DX-120 system loop start CO line interface capacity to a maximum of eight loop start CO line ports in each KSU (16 total loop start CO line ports when used in KSU 1 & 2).• When adding a COM4 to either KSU, connect to the 408M/E via the COM4 module ribbon cable.- This ribbon cable has the logical system address of SLOT 5 in both cabinet 1 (KSU1-408M) and cabinet 2 (KSU2-408E).• COM4 modules are installed using four 2.0 cm (brass) standoffs.• Always install the COM4 module beneath the CPM module (in KSU1) by first removing the CPM, installing the COM4, and then re-installing the CPM. This is required whenever you install the In-Skin Voice Processor.

 

Condition: Refurbished - 90 Day Warranty)  $25.00 (Free USPS shipping)

Call or E-Mail to Order. 

 

DX-80 & DX-120 7230 APM4 (1 Available)

The card does not include the box, but it is in its original, unopened anti-static bag.

The APM4 provides four separate analog device ports. This allows the DX-80 to support auxiliary office equipment such as fax machines, PC/FAX modems, and analog telephones (single line telephones). The APM4 generates -30VDC and 20-25Hz, 50V square wave ringing for operation.

The APM4 is equipped with a heartbeat LED that indicates processing activity on the PCB; the APM4 peripheral processor is operating when the heartbeat LED is flashing.

When an APM4 is installed via J2 or J3, it takes the place of DPM8 modules that might be installed in those locations. Therefore APM4 modules installed using J2 or J3 will reduce the total number of Digital Port Modules (DPM8) possible.

Condition: New - Open Box (1 Year Warranty)  $50.00 (Free USPS Shipping)

Call or E-Mail to Order. 

 

Telephones

7261 User Guide.pdf 1.1MB